NDP-15FPN
NDP-15FPN Yamada AODD Diaphragm Pump Selangor, Malaysia, Kuala Lumpur (KL), Seri Kembangan Supplier, Suppliers, Supply, Supplies | Merns (M) Sdn Bhd

specification

 

Nominal diameter 1/2 ″ (15A)
Material connection Inlet Rc1 / 2
Discharge port
Air connection Supply port Rc1 / 4 (with air cock)
exhaust port Rc3 / 8 (with muffler) *
Service air pressure 0.2 to 0.7 MPa
Discharge pressure 0.7MPa
Discharge rate / cycle 70mL
Slurry limit (maximum passing particle diameter) 1mm or less
Mass -15BA NDP: 4.1Kg
NDP-15BS ¡õ: 6.3Kg
NDP-15FP ¡õ: 3.5Kg
NDP-15FVT: 4.3Kg

* The silencer is built into the pump body.
Rc3 / 8 screw holes are machined for connecting hoses to guide exhaust to ducts.

Since the NDP-15 series uses the DP-10 series diaphragm, select the NDP-20 series that is one size up for large-scale operation at 20L / min or higher. NDP-15BA ¡õ series uses nylon (PA) as the material for the valve receiver. Pay attention to corrosion resistance. Not suitable for MEK etc.

 

Please download the parts exploded view and parts list from the data download page → Download data

Body (wetted part) material Diaphragm material
C:
Chloroprene
(CR)

N:
Nitrilgam
(NBR)

T:
Fluorine resin
(PTFE)

H:
Polyester type thermoplastic elastomer
(TPEE)

S:
Polyolefin-based thermoplastic elastomer
(TPO)
A: Aluminum alloy (ADC12) NDP-15BAC
(851946)
NDP-15BAN
(851947)
NDP-15BAT
(851945)
NDP-15BAH
(851948)
NDP-15BAS
(852680)
S: Stainless steel (SCS14) NDP-15BSC
(851958)
NDP-15BSN
(851959)
NDP-15BST
(851957)
NDP-15BSH
(851960)
NDP-15BSS
(852681)

P: Polypropylene (PPG)

NDP-15FPC
(851903)
NDP-15FPN
(851943)
NDP-15FPT
(851698)
NDP-15FPH
(851905)
NDP-15FPS
(852683)

V: Polyolefin full oil (PVDF)

--- --- NDP-15FVT
(852141)
--- ---

Note) Clicking the model / product number will display the parts list and parts exploded view.
 

Main material

 

Model

NDP-15BA ¡õ

NDP-15BS

NDP-15FP

NDP-15FVT

Ball valve Flat valve

NDP-15FP ¡õ / NDP-15FVT ・ ・ ・ PTFE
Other NDP-15B ¡õ¡õ ・ ・ ・ Same as diaphragm material

Valve seat

A5056

 

SUS316

 

PPG

PVDF

Valve holder

PA

Center disc

A5056

PPG (SUS304 *)

PVDF (SUS304 *)

* SUS304 is insert material

¡ï Valve model
NDP-15BA ¡õ / NDP-BS ¡õ ・ ・ ・ Ball valve
NDP-15FP ¡õ / NDP-15FVT ・ ・ ・ Flat valve ¡ï The flat valve type cannot handle slurry.
¡ï The initial self-priming lift is 1m for all models.

 

The maximum operating pressure of the body wetted part resin type (FP ¡õ / FVT) is
It depends on the liquid temperature. Be sure to check the liquid temperature-maximum working pressure diagram.

Please leave your enquiry here, we will reply as soon as possible.


*only support gif, jpeg, jpg, png, pdf
Switch To Desktop Version